![karma motif setup cubase karma motif setup cubase](https://i.ytimg.com/vi/d_S63n3V71Y/maxresdefault.jpg)
![karma motif setup cubase karma motif setup cubase](http://www.moessieurs.com/images/36ckmo.jpg)
- #KARMA MOTIF SETUP CUBASE INSTALL#
- #KARMA MOTIF SETUP CUBASE DRIVER#
- #KARMA MOTIF SETUP CUBASE SERIES#
- #KARMA MOTIF SETUP CUBASE WINDOWS#
At some point you might connect a microphone to the XF or you may have cause to route a single instrument to its own track. (That assignment typically is made when you decide to route a Motif XF PART to an assignable output. You do not have to worry about changing these to active, they will change when you actually assign something to use these inputs into the Cubase program. The "Inactive" status on the "Motif XF 1" - "Motif XF 14" simply means that as of yet, nothing is assigned to use those inputs into Cubase. You will see the word "Active" in the STATE column - this is a status report and indicates that currently these inputs are in use by Cubase. The first are the MAIN Left/Right OUTPUTS of the Motif XF arriving in Cubase as "Motif XF Main L" and "Motif XF Main R". You will see the PORTS listed by their names (if you have properly installed the Motif XF Extension). They are seen as audio (IN) inputs to Cubase. The screen shot above shows the 16 Audio OUTPUT buses available from the Motif XF. If you highlight that you will see the CONTROL PANEL where you can set your buffer size. The option just below VST AUDIO SYSTEM will be "Yamaha Steinberg FW". Move down to the VST AUDIO SYSTEM item and verify that the Yamaha Steinberg FW is selected as the ASIO DRIVER. It will be assigned as your Remote Control device and the MIDI IN and MIDI OUT ports will be assigned. In the next folder "REMOTE DEVICES" highlight the Motif XF item. Remote Control commands must be kept discreet, so as not to interfere with normal music performance. You do not want to mark the Motif XF REMOTE port in the In All MIDI Inputs column. Make sure that only these devices are marked in the "In 'All MIDI Inputs'" column Typically this is either your Motif XF keyboard (Motif XF Main) or any MIDI controller connected to its back panel Motif XF MIDI IN jack. Here you will be able to select the device(s) that will be your MIDI controller.
#KARMA MOTIF SETUP CUBASE SERIES#
(called “Studio Setup.” in Cubase series 9) > MIDI > MIDI Port Setup
![karma motif setup cubase karma motif setup cubase](http://www.motifator.com/images/uploads/YSFWwinASIO.jpg)
Go to DEVICES (called “Studio” in Cubase series 9) > DEVICE SETUP.
#KARMA MOTIF SETUP CUBASE DRIVER#
Expect audio output to be sent to the sound system connected to the main LEFT/RIGHT outputs of the Motif XF.īecause you have installed the Motif XF Extension, Cubase will ask you if you want to use the Yamaha Steinberg FW driver as your ASIO driver. This sets your Motif XF as your soundcard for your computer. The current IEEE1394 Firmware version of your FW16E will be shown.
#KARMA MOTIF SETUP CUBASE WINDOWS#
Here the Driver can be used for your Windows applications (this is not necessary for Cubase, you will setup for Cubase within that program) but if you would like your Windows Media Player or other Windows audio applications (games, etc) to use use your Motif XF studio system (that is, route audio via the XF audio oututs) set the AUDIO ROUTING here to use the "Motif XF Main L/R" Outputs.Ĭlick on the tab(s) that identifies your connected device(s): Motif XF7 Here you will be able to set the Sample Rate (44.1kHz, 48kHz, 88.2kHz or 96kHz), the Word Clock Master (Motif XF7), and the Clock Source (Internal)Ĭlick on the WDM > AUDIO ROUTING option. If you have the LARGE or SMALL icon view you will see it listed as "Yamaha Steinberg FW"ĭouble click the icon to open the Yamaha Steinberg FW control panel. It will be listed under the heading "Hardware and Sound" if you have the "Category" view. Press to write this preference to your Flash ROM.ĭepending on your default view (Category, Large icon, Small icon) you need to find the Yamaha Steinberg FW icon. When you are using the Motif XF with the Yamaha Steinberg FW driver (YSFW) you need to verify the following settings in your Motif XF: The Motif XF Extension is an addition to Cubase that will allow it to recognize the Motif XF ports by name, and it will automatically do much of the audio and MIDI setup (like assigning Remote Control Device ports, and upon launch you will be asked if you want to use the Yamaha Steinberg FW driver as your ASIO driver, etc). _ Motif XF Extension version 1.1.1 (or later) for Windows _ Yamaha Steinberg FW Driver version 1.6.6 (or later) for your particular Windows operating system
#KARMA MOTIF SETUP CUBASE INSTALL#
Setting up the XF for use with Cubase via FireWire on a Windows computer.Ī quick setup guide to get going with Cubase and your Motif XF via the FW16E (firewire) option.ĭownload and install the following items: